Home Rewiring in Ventura County

Most whole home rewires for a 2 to 4 bedroom house run $24,000 to $32,000. Your drywall stays on. We work from the attic and crawl space, behind your finished walls and ceilings. You get a written price before any work starts, and anything we find hidden in a wall is priced for your OK before we touch it.

California C10 license #889112. 22 years in business.

Living room in an older Craftsman home with wood paneling, built-in bookshelves, a tile fireplace and warm wall sconces

We treat your home like it's ours

Most people who call us about a rewire love their house. That is usually why they are rewiring it. And the first question is almost always the same: what is this going to do to my home?

A rewire sounds like demolition. It isn’t. Most of the work happens where you never look: in the attic, under the floor, and inside the walls you already have. What you notice when we are done is new outlets and switches, lights that work the way they should, and the quiet of not worrying about your wiring anymore.

We have done this in 1910 farmhouses, 1920s Craftsmans and 1950s ranch homes, many with the family living there the whole time. Plaster walls, original wood paneling, old tile: we have worked around all of it, and we plan for it before the first day. At the end of every day your house is clean and livable. At the end of the job it looks like your home, not a job site.

Original push button light switches set in old wood paneling in a historic home

Your drywall stays on

We fish new wire from the attic and crawl space and bring it out through the openings already there for your outlets, switches and lights. When a wall has to be opened, we keep the hole small, put it where it shows least, and show you before we cut.

Covered and cleaned every day

Floors and finished surfaces are covered, dust is kept down, and we clean up before we leave. We work room by room so only part of the house is without power at a time.

Special finishes are planned for

Plaster, wood paneling, tile backsplashes, beamed ceilings and clay roof tile are noted at the walkthrough and written into your price.

Patching is by others

We tell you that before you sign, and we show your patcher where every opening is.

What a rewire costs

These ranges come from the rewire estimates we wrote in 2026. Square footage, the number of outlets and lights, and how easy the house is to get into move the price more than anything else.

Whole home rewires, by size

Home size Typical price
Under 1,000 sq ft $20,000 to $24,000
1,000 to 1,500 sq ft (most 2 to 4 bedroom homes) $24,000 to $32,000
1,500 to 1,800 sq ft $30,000 to $37,000
Over 1,800 sq ft, 5 bedrooms and up, or a custom home From $40,000, quoted per project
Add a 200 amp panel upgrade Add $4,000 to $5,000

Most of our whole home rewires land between $18 and $21 per square foot for the rewire itself.

Partial rewires and smaller jobs

Your job Typical price
Partial rewire, lighting and outlet circuits, one story $14,000 to $19,000
Knob and tube replaced in a few rooms $5,000 to $11,000
Knob and tube removed from the attic, new circuits run to existing outlets $2,400 to $4,000
Garage rewire $2,000 to $2,700
ADU or detached office rewire $2,300 to $7,500
Aluminum wiring repaired at every outlet, switch and light $2,500 to $3,500

Prices updated November 2026. These are typical prices from jobs we quoted in 2026, not a quote for your home. They do not include city or county permit fees, which we pass through at cost, our $350 fee for pulling and managing the permit, or any fees SCE charges. Drywall, plaster and paint patching are by others.

What moves the price

  • Square footage, and the number of outlets, switches and lights code requires
  • Attic and crawl space access. A roomy attic and crawl space is the easiest; a tight attic with no crawl space is the hardest
  • Plaster and lath walls, which are slower and more fragile than drywall
  • One story or two
  • Whether you live in the house during the work
  • Whether the panel needs replacing too

Knob and tube, cloth and aluminum wiring

Knob and tube was standard until about the 1940s and is the most common reason a home here gets rewired, especially in older parts of Ventura, Oxnard, Ojai, Oak View and Santa Paula. It has no ground wire, the insulation gets brittle, and it was never built for today’s loads. Insurance companies and lenders often ask for it to be replaced.

We disconnect it, take out everything we can reach in the attic and crawl space, and leave the dead wire sealed inside finished walls. Pulling it out of every wall would mean opening every wall.

Cloth covered wiring from the 1940s and 1950s gets the same treatment: new copper wire, old wire disconnected at the panel.

Aluminum wiring from about 1965 to 1973 usually does not need a full rewire. The trouble is at the connections, so we repair every one with AlumiConn connectors or the COPALUM crimp method and put in new outlets and switches. It usually takes one to two days.

Two kinds of knob and tube job

A full rewire to code replaces every circuit, adds outlets so none of your walls are short, adds the circuits a kitchen and laundry need, and adds GFCI and AFCI protection and smoke and CO alarms. It gets a permit and two inspections. This is what an insurer or lender normally wants.

A like for like swap runs new wire to the outlets and lights you already have and adds nothing. It costs less, but it is not a code rewire and the house keeps the outlet count it started with.

We will price both if you ask, and we will tell you plainly which one your inspection report, insurer or lender actually needs. Send us the letter and we will read it before you spend anything.

Older panels

A rewire adds 25 to 35 new circuits, and many older panels do not have room. Zinsco, Federal Pacific and Pushmatic panels should be replaced anyway. We do not add circuits to Zinsco or Federal Pacific panels. See our panel upgrade page for those prices.

New electrical panel with neatly routed wiring and new breakers

Everything in the price

  • New copper wiring to every outlet, switch and light
  • New boxes, outlets, switches and cover plates throughout
  • Outlets added where code requires them
  • Dedicated circuits for the kitchen, laundry, bathrooms and major appliances
  • GFCI and AFCI protection where code requires it, and tamper resistant outlets
  • Hardwired, interconnected smoke and carbon monoxide alarms with battery backup
  • New grounding and bonding to current code
  • Every circuit labeled and tested
  • We pull the permit, schedule the inspections and meet the inspector (permit fees and our $350 permit fee are extra)

How it works

  1. Send photos

    Send us your square footage, bedroom and bathroom count, and photos of your panel, your attic and a few outlets. Or we come take a look.

  2. Get your price

    You get a written price, with anything optional priced on its own line.

  3. Permit

    We pull it. In the City of Ventura a whole home rewire permit is issued the same day. Partial rewires and most other cities take about 3 weeks to 2 months.

  4. Rough in and inspection

    New wire, boxes and circuits go in. The city inspects before any wall is closed.

  5. Finish and final

    Outlets, switches, lights and alarms go in, every circuit is tested, and the city does the final inspection.

How long it takes

With a two person crew, a 1,000 to 1,200 sq ft home takes about 2 to 2.5 weeks, 1,200 to 1,500 sq ft about 2.5 to 3 weeks, and 1,500 to 1,800 sq ft about 3 to 3.5 weeks. Add a day for a panel upgrade, plus the wait for SCE, which is often the longest part. Rewires are billed in stages as the work is done, not all up front.

Rewires we have done

  • Ventura: full rewire of a 1955 four bedroom home with a 200 amp service upgrade
  • Ventura: full rewire of a 1947 home with the family living in it, original wood paneling kept, new sub panel and EV charger circuit
  • Ventura: cloth wiring replaced in three bedrooms, the hall, living room and dining room, with fan rated boxes added
  • Ojai: aluminum wiring repaired at all 28 outlets and switches
  • Santa Paula: two bedrooms, a hall and a bath rewired in a home with no attic or crawl space access, plus a 200 amp panel

Rewire questions

How much does it cost to rewire a house?

For a typical 2 to 4 bedroom home of 1,000 to 1,500 sq ft in Ventura County, most whole home rewires run $24,000 to $32,000, or about $18 to $21 per square foot, before permit fees and before a panel upgrade if you need one. Square footage, the number of outlets and lights, and how hard the house is to get into set the final number.

How long does a rewire take?

About 2 to 3.5 weeks for most homes from 1,000 to 1,800 sq ft with a two person crew. Add a day if the panel is being replaced, plus the wait for SCE.

Can I live in the house during a rewire?

Yes, and many of our customers do. It takes a little longer and costs a little more because we work around furniture and belongings. Tell us up front so the price is right. If the rooms can be cleared ahead of us, the job goes faster.

Will I be without power the whole time?

No. We work room by room, so only the area we are working on is off. If the panel is being replaced, there is one full outage on that day, and power is normally back the same day.

Will you cut up my walls?

As little as possible. We work from the attic and crawl space and use the openings already there. When a wall has to be opened, we keep it small, put it where it shows least, and show you first. Patching and paint are by others.

Do you remove all the old knob and tube?

We disconnect all of it and remove what we can reach in the attic and crawl space. Dead wire inside finished walls stays where it is, because taking it out would mean opening every wall.

My insurance company says I have knob and tube. What do they need?

Usually a full rewire to code with a permit and a final inspection, not a like for like swap. Send us the letter and we will tell you which job satisfies it before you spend anything.

Do I need a permit to rewire my house?

Yes. Every rewire gets at least two inspections, one before the walls are closed and one at the end. In the City of Ventura a whole home rewire permit is issued the same day. We pull the permit and meet the inspector.

Do I need a new panel too?

Often. A rewire adds 25 to 35 new circuits, and many older panels do not have room. Zinsco, Federal Pacific and Pushmatic panels should be replaced regardless. See our panel upgrade page. We check your panel before we price the job.

Can I rewire in stages?

Yes. Some customers replace the panel now and rewire later, or do the house in sections. We price each stage on its own. Doing it in stages costs more in total than doing it all at once.

Where do you work?

We work across Ventura County and southern Santa Barbara County, including Ventura, Oxnard, Camarillo, Port Hueneme, El Rio, Ojai, Oak View, Mira Monte, Santa Paula, Fillmore, Somis, Moorpark, Simi Valley, Santa Rosa Valley, Thousand Oaks, Newbury Park, Westlake Village, Oak Park, Carpinteria, Summerland, Montecito, Santa Barbara and Goleta.

Call (805) 650-9054, Monday to Friday, 8 am to 4 pm, or send us photos for an estimate. California C10 license #889112.

Finished sunroom in an older home with wood walls, a beamed ceiling, a woven pendant light and a wall of windows

Get your rewire price

Send us your square footage, bedrooms and bathrooms, and photos of your panel, your attic and a few outlets, and we will send back a written price.